Rain Bird 100-DVF-MB 1" (26/34)

Plastic Residential Irrigation Valves

Rain Bird manufactures only the highest quality valves. Use DV/DVF series valves in locations where the use of a separate pressure vacuum breaker (PVB) or a double-check valve is required by city codes to protect against back flow. Check your local city codes to determine what type of valves are required.

All of our valves work with any standard sprinkler timer.

• Double-filtered pilot-flow design for maximum reliability.
• Balanced-pressure diaphragm for long life.
• External bleed to manually flush system of dirt and debris during installation and system start-up.
• Internal bleed for spray-free manual operation.
• Energy-efficient, low-power encapsulated solenoid with captured plunger and 90-mesh (200 micron) solenoid filter.
• Buna-N diaphragm with self-cleaning 90 mesh (200 micron) pilot water filter and captive spring.
• Operates in low-flow and Xerigation® applications when the RBY filter is installed upstream.
• 1.25" (3,2 cm) stainless steel phillips head screws.
• Accepts latching solenoid for use with Rain Bird battery-operated controllers.
• Available as:
  • 3/4" (20/27) and 1" (26/34) standard in-line configuration.
  • 1" (26/34) Slip-by-Slip (SS) configuration for low cost, solvent-weld installations.
  • 1" (26/34) Angle (A) configurations for flexible installations especially when submains are deep.
  • 1" (26/34) Male-by-Male (MM) thread configuration for quick and easy manifolding.
  • 1" (26/34) Male-by-Barb (MB) and 1" Male-by-1.25" Barb male thread inlet by barb outlet configuration for installation with poly pipe.
• Unique, easy-to-turn patented pressure assisted flow control mechanism (DVF models only).
• Five-year trade warranty.

075-DV 3/4" (20/27)	100-DV 1" (26/34)*
100-DV-SS 1" (26/34)	100-DV-A 1" (26/34)
100-DV-MB 1" (26/34)	100-DVF 1" (26/34)*
100-DVF-SS 1" (26/34)	100-DVF-A 1" (26/34)
100-DVF-MB 1" (26/34)
*Available with BSP threads.
Rain Bird recommends flow rates in the supply line not to exceed 7.5 ft./sec. (2,3 m/s) in order to reduce the effects of water hammer.
DV Series valves cannot be used with PRS pressure regulating modules.

• Pressure: 15 to 150 psi (1,0 to 10,4 bar)
• 075-DV Flow: 0.2 to 22 GPM (0,05 to 5,0 m³/h; 0,01 to 1,39 l/s). For flows below 3 GPM (0,75 m3/h; 0,21 l/s) or any Xerigation® application, use RBY-075-200MX Filter installed upstream.
• 100-DV Flow): 0.2 to 40 GPM (0,05 to 9,08 m³/h; 0,01 to 2,52 l/s). For flows below 3 GPM (0,75 m3/h; 0,21 l/s) or any Xerigation® application, use RBY-100-200MX Filter installed upstream.
• 100-DVF Flow (non-union): 0.2 to 40 gpm (0,75 m³/h; 0,21 l/s); for flows below 3 gpm or any Xerigation application, use RBY-100-200MX Filter installed upstream.
• Temperature: Up to 110° F (43° C)
• Ambient air temperature: Up to 125° F (52° C)
• 24 VAC 50/60 Hz (cycles per second) solenoid power requirement:
• 0.30 A (7.2 VA) inrush current; 0.23 A (5.5 VA) holding current
• Solenoid coil resistance: 38 Ohms

Dimensions:

• Height: 4 1/2" (11,4 cm)
• Height (Angle): 5 1/2" (14 cm)
• Width: 3 1/3" (8,4 cm)
• Length: 4 3/8" (11,1 cm)
• Length (Angle): 3 3/4" (9,5 cm)
• Length (MM): 5 3/8" (13,6 cm)
• Length (MB): 5 3/4" (14,6 cm)

 Brochure (PDF: 213 KB)
 Sell Sheet (PDF: 274 KB) 
 Instruction Manual (PDF: 397 KB)
 Pressure Loss Charts (PDF: 113 KB)
 Valve Installation/Maintenance Tips (PDF: 229 KB)
 Replacement Parts (PDF: 126 KB)
 Tech Specs (PDF: 475 KB)